The Linux Community Forum

Support => General Help & Advice => Topic started by: nvs on March 18, 2014, 12:18:01 pm

Title: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 18, 2014, 12:18:01 pm
Cannot connect to internet leoxsys LEO NANO 150N wireless usb adapter even after
going through all the steps of topic 11154 on my linux mint 16 (petra) desktop.
The vendor ID 148f is MediaTek and 7601 is productID. Is there a linux driver for 7601
that can be compiled and integrated in the system?
The relevant outputs are listed below.

[email protected] ~ $ inxi -n
Network:   Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
           IF: eth0 state: up speed: 100 Mbps duplex: full mac: 00:20:ed:ff:ff:ff
           Card-2: Ralink
           IF: N/A state: N/A speed: N/A duplex: N/A mac: N/A

[email protected] ~ $ uname -a
Linux mint 3.11.0-12-generic #19-Ubuntu SMP Wed Oct 9 16:12:00 UTC 2013 i686 i686 i686 GNU/Linux

[email protected] ~ $ lsusb
Bus 001 Device 003: ID 148f:7601 Ralink Technology, Corp.

[email protected] ~ $ sudo lshw -C network
  *-network               
       description: Ethernet interface
       product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: [email protected]:02:00.0
       logical name: eth0
       version: 02
       serial: 00:20:ed:ff:ff:ff
       size: 100Mbit/s
       capacity: 1Gbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s
       resources: irq:42 ioport:d000(size=256) memory:e1110000-e1110fff memory:e1100000-e110ffff memory:e1120000-e112ffff
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 18, 2014, 12:35:23 pm
Hi nvs, and welcome to the forum :)

Whilst I've never tried compiling these against the 3.11 kernel, they certainly compile against 3.8

In best Blue Peter fashion .. here's one I prepared earlier:
http://peppermintos.net/viewtopic.php?p=41805#p41805 (http://peppermintos.net/viewtopic.php?p=41805#p41805)

I'll repost my instructions here though:-

Ralink wireless driver 148f:7601 (for wireless adapters with the Ralink MT7601U chipset)

Make sure you have an active internet connection (connect to your router by an ethernet cable if you need to), then open a terminal and run these commands in sequence:
Code: [Select]
sudo apt-get install linux-headers-generic build-essential
then
Code: [Select]
mkdir ~/MT7601-Driver
then
Code: [Select]
cd ~/MT7601-Driver
then
Code: [Select]
wget https://dl.dropboxusercontent.com/u/11876059/DPO_MT7601U_LinuxSTA_3.0.0.4_20130913.tar.gz
then
Code: [Select]
tar xvf DPO_MT7601U_LinuxSTA_3.0.0.4_20130913.tar.gz
then
Code: [Select]
cd ~/MT7601-Driver/DPO_MT7601U_LinuxSTA_3.0.0.4_20130913
then
Code: [Select]
make
then
Code: [Select]
sudo make install
then
Code: [Select]
sudo modprobe mt7601Usta
Did wireless spring to life ?

If so, check it survives a reboot.

--
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 18, 2014, 02:43:04 pm
Mark,

You are great. It worked and survived reboot.

Thank you very much.

nvs
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 18, 2014, 04:24:06 pm
You're most welcome :)
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 19, 2014, 12:07:13 pm
I tried to set up a wireless network connection from menu->preferences->network connections and entered connection name, SSID of my Belkin router,
mode infrastructure, router mac address for BSSID, and USB mac address for device mac address. In the router I added usb mac address in wireless access
control list and in wlan section of lan interface. With that set up I tried to connect to internet after disconnecting the wired connection. I could not connect to internet.

What am I doing wrong?
 inxi -n
Network:   Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
           IF: eth0 state: up speed: 100 Mbps duplex: full mac: 00:20:ed:ff:ff:ff
           Card-2: Ralink driver: rt2870
           IF: ra0 state: down mac: 12:34:56:00:09:43

After executing ifup -a,
 inxi -n
Network:   Card-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
           IF: eth0 state: up speed: 100 Mbps duplex: full mac: 00:20:ed:ff:ff:ff
           Card-2: Ralink driver: rt2870
           IF: ra0 state: down mac: 12:34:56:00:09:43
ra0 state remains down.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 19, 2014, 10:50:52 pm
OK, it seems to have gone back to using the rt2870 driver

What's the output from:
Code: [Select]
sudo lshw -C network
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 20, 2014, 12:03:06 pm
[email protected] ~ $ sudo lshw -C network
  *-network               
       description: Ethernet interface
       product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: [email protected]:02:00.0
       logical name: eth0
       version: 02
       serial: 00:20:ed:ff:ff:ff
       size: 100Mbit/s
       capacity: 1Gbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s
       resources: irq:42 ioport:d000(size=256) memory:e1110000-e1110fff memory:e1100000-e110ffff memory:e1120000-e112ffff
  *-network DISABLED
       description: Wireless interface
       physical id: 1
       logical name: ra0
       serial: 12:34:56:00:09:43
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=RALINK WLAN multicast=yes wireless=Ralink STA

[email protected] ~ $ lsusb
Bus 001 Device 002: ID 148f:7601 Ralink Technology, Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 045e:00cb Microsoft Corp. Basic Optical Mouse v2.0
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

[email protected] ~ $ sudo lsmod | grep 7601
mt7601Usta            744038  0


Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 20, 2014, 12:05:26 pm
post the full output from
Code: [Select]
lsmod
and
Code: [Select]
rfkill list
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Emegra on March 20, 2014, 12:06:47 pm
@nvs

If your copy and pasting these commands into the terminal, the second command should be

Code: [Select]
rfkill list
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 20, 2014, 12:37:43 pm
fixed above .. thanks Emegra :)
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 20, 2014, 01:30:57 pm
[email protected] ~ $ lsmod
Module                  Size  Used by
cfg80211              401436  0
bnep                   18893  2
rfcomm                 53664  0
bluetooth             323534  10 bnep,rfcomm
binfmt_misc            13140  1
coretemp               13195  0
gpio_ich               13229  0
ppdev                  17391  0
mt7601Usta            744038  0
snd_hda_codec_realtek    45473  1
snd_hda_intel          42658  3
snd_hda_codec         164003  2 snd_hda_codec_realtek,snd_hda_intel
microcode              18830  0
snd_hwdep              13272  1 snd_hda_codec
snd_pcm                89488  2 snd_hda_codec,snd_hda_intel
dm_multipath           22402  0
scsi_dh                14458  1 dm_multipath
snd_page_alloc         14230  2 snd_pcm,snd_hda_intel
snd_seq_midi           13132  0
snd_seq_midi_event     14475  1 snd_seq_midi
snd_rawmidi            25094  1 snd_seq_midi
lpc_ich                16864  0
snd_seq                55383  2 snd_seq_midi_event,snd_seq_midi
serio_raw              13189  0
snd_seq_device         14137  3 snd_seq,snd_rawmidi,snd_seq_midi
snd_timer              24447  2 snd_pcm,snd_seq
parport_pc             31981  1
snd                    60790  16 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi
mac_hid                13037  0
soundcore              12600  1 snd
lp                     13299  0
parport                40795  3 lp,ppdev,parport_pc
hid_generic            12492  0
usbhid                 47361  0
hid                    87192  2 hid_generic,usbhid
dm_mirror              21715  0
dm_region_hash         15984  1 dm_mirror
dm_log                 18072  2 dm_region_hash,dm_mirror
i915                  589697  3
video                  18777  1 i915
i2c_algo_bit           13197  1 i915
drm_kms_helper         46867  1 i915
drm                   242354  4 i915,drm_kms_helper
r8169                  61434  0
mii                    13654  1 r8169
[email protected] ~ $ rfkill list
[email protected] ~ $
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 20, 2014, 02:24:37 pm
Undo whatever you did .. ie. delete all wireless connections in networkmanager.

Then reboot.

Are you sure you haven't disabled wireless with a hardware switch ?

I'm baffled by your not having any output from "rfkill list" .. and why the card has become "disabled"

Does removing the driver, then reinserting it make a difference ?:
Code: [Select]
sudo modprobe -r mt7601Usta
then
Code: [Select]
sudo modprobe mt7601Usta
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 20, 2014, 06:13:02 pm
After I deleted WiFi1 only Ethernet connection 1 is left as shown below.

[email protected] /etc/NetworkManager/system-connections $ ls
Ethernet connection 1

[email protected] ~ $ sudo modprobe -r mt7601Usta
[sudo] password for ravi:
[email protected] ~ $ sudo modprobe mt7601Usta
[email protected] ~ $

After that I created WiFi1 as indicated here

[email protected] ~ $ sudo cat /etc/NetworkManager/system-connections/WiFi1
[sudo] password for ravi:
[connection]
id=WiFi1
uuid=70f89d0d-4558-4133-b5a4-a8e8fa12105e
type=802-11-wireless

[802-11-wireless]
ssid=SKS
mode=adhoc
bssid=EC:1A:59:90:40:6C
mac-address=12:34:56:00:09:43
security=802-11-wireless-security

[802-11-wireless-security]
key-mgmt=wpa-psk
proto=rsn;
pairwise=ccmp;
group=ccmp;
psk=wh0ami?!

[ipv4]
method=auto

[ipv6]
method=auto

When I disconnected the wired Ethernet connection and I tried to switch on wireless connection
the connection name HOME appeared. Trying to turn that on repeatedly kept asking for password
authentication but never established connection. I deleted that connection. Rebooted the system.
Created a new connection with mode Ad-hoc.
[email protected] ~ $ sudo cat /etc/NetworkManager/system-connections/WiFi1
[sudo] password for ravi:
[connection]
id=WiFi1
uuid=70f89d0d-4558-4133-b5a4-a8e8fa12105e
type=802-11-wireless

[802-11-wireless]
ssid=SKS
mode=adhoc
bssid=EC:1A:59:90:40:6C
mac-address=12:34:56:00:09:43
security=802-11-wireless-security

[802-11-wireless-security]
key-mgmt=wpa-psk
proto=rsn;
pairwise=ccmp;
group=ccmp;
psk=********

[ipv4]
method=auto

[ipv6]
method=auto

Now clicking on the network icon at bottom right, disonnecting wired connection and clicking on
wireless shows unavailable and automatically creates a connection “Auto HOME” and goes into
authentication loop endlessly generating additional “Auto HOME” connections.

I am frustrated and ready to give up.  Anyway, it is 11:30 and I feel sleepy. Will resume tomorrow.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 20, 2014, 06:24:18 pm
Why are you manually creating the connection ? .. is your wireless hidden ?

and why are you setting it as an adhoc network
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 22, 2014, 09:36:45 am
Yes, I have set router to not broadcast SSID and I have also entered LEO NANO
ethernet address in wireless access control list and in the WLAN section of the LAN
interface.

After reading your comment I changed the Belkin router configuration to default
configuration and that created a wireless connection “Auto belkin.06C” listed below.

earth system-connections # cat Auto\ belkin.06C
[connection]
id=Auto belkin.06C
uuid=2bd95e60-74ca-4850-9bc7-37af1dc76fe1
type=802-11-wireless

[802-11-wireless]
ssid=belkin.06C
mode=infrastructure
security=802-11-wireless-security

[802-11-wireless-security]
key-mgmt=wpa-psk
auth-alg=open
psk=********

[ipv4]
method=auto

[ipv6]
method=auto

This connection is established but I cannot connect to the internet.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 22, 2014, 12:00:31 pm
Are you able to ping both your routers IP and the IP of Google.com ?

What's the output from:
Code: [Select]
ping -c 5 173.194.34.131
and
ping -c 5 <ip.address.of.router>
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 22, 2014, 01:32:45 pm
No, I cannot even ping 192.168.2.1 the IP address of my Belkin router with the connection wifi1, a hidden network, listed below.
I probably need to do something in ipv4 setting but don't know what. It has only one entry method "Automatic DHCP"

earth system-connections # cat wifi1
[connection]
id=wifi1
uuid=d2033f03-1280-4b44-83b4-0428249ca6ac
type=802-11-wireless

[802-11-wireless]
ssid=SKS
mode=infrastructure
bssid=EC:1A:59:90:40:6C
mac-address=12:34:56:00:09:43
security=802-11-wireless-security

[802-11-wireless-security]
key-mgmt=wpa-psk
psk=*********

[ipv4]
method=auto

[ipv6]
method=auto



Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 22, 2014, 06:09:13 pm
For now disable mac address filtering and unhide the network SSID in your router .. you can enable them again later, but for now it's complicating things, I want to see if the network adapter/drivers are actually working properly or not.

In network manager delete any wireless connections.

click the networkmanager icon in your system tray .. is your network listed ?

if so, click on it to connect .. enter your Mint password and wireless key .. did it connect ?

is the internet available ?
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 25, 2014, 06:48:06 pm
Sorry for the delay. I was visiting my sister in Mumbai. Now I am back to U.S. I hope my registration will be forever.
I will ask my niece-in-law who is unfamiliar with linux but well-versed in windows to make changes to configuration
that you will recommend.

After I set the router to default configuration I got connected to the router but not to the internet. Here is what I got.
[email protected] ~ $ sudo cat /etc/NetworkManager/system-connections/*b*
[sudo] password for ravi:
[connection]
id=Auto belkin.06C
uuid=8ca4e7bd-088c-4c51-8aac-4add9bbe5a2e
type=802-11-wireless

[802-11-wireless]
ssid=belkin.06C
mode=infrastructure
security=802-11-wireless-security

[802-11-wireless-security]
key-mgmt=wpa-psk
auth-alg=open
psk=********

[ipv4]
method=auto

[ipv6]
method=auto


[email protected] ~ $ ping -c5 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
64 bytes from 192.168.2.1: icmp_seq=1 ttl=30 time=1.56 ms
64 bytes from 192.168.2.1: icmp_seq=2 ttl=30 time=1.37 ms
64 bytes from 192.168.2.1: icmp_seq=3 ttl=30 time=1.41 ms
64 bytes from 192.168.2.1: icmp_seq=4 ttl=30 time=1.53 ms
64 bytes from 192.168.2.1: icmp_seq=5 ttl=30 time=1.50 ms

--- 192.168.2.1 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4006ms
rtt min/avg/max/mdev = 1.376/1.478/1.567/0.080 ms

Networking screen for belkin.06C shows

belkin.06C
Connected
Hardware Assress 12:34:56:00:09:43
Security WPA, WPA2
Strength Excellent
Link Speed 54 Mb/s
IP Address 192.168.2.2
Default Route 192.168.2.1
DNS 192.168.2.1

DNS address above is that of the router. The network connection has no routing information added.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 25, 2014, 08:45:44 pm
So what happens now if you try pinging google.com by IP
Code: [Select]
ping -c 5 173.194.41.166
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: SeZo on March 25, 2014, 08:54:41 pm
You could also try to trace it to see how far it gets:
Code: [Select]
sudo traceroute -I 173.194.41.166
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: nvs on March 26, 2014, 07:24:07 pm
It reports that the network is unreachable. When I added mtnl name server ip address in ipv4 setting and
left DHCP automatic it gave the same result.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on March 26, 2014, 07:28:40 pm
so you can ping the router, but not the web ?

can you access you routers web interface (wirelessly) ?
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: chemicalfan on March 27, 2014, 09:07:45 am
And the wired connection works perfectly? If you connect an Ethernet cable to router, you can access the internet?

Could be some kind of filter/firewall issue within the router....you'll probably need to connect the cable anyway to access those settings
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: mandeepmails on June 07, 2014, 05:56:14 pm
hi there,

i went through the all steps with ubuntu14.04 and Leoxsys (posted most of the commands output so that you can guide me, where i'm missing

[email protected]:~$ iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

[email protected]:~$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:e0:4c:64:05:d2 
          inet addr:192.168.1.2  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::2e0:4cff:fe64:5d2/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:20 errors:0 dropped:0 overruns:0 frame:0
          TX packets:70 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2487 (2.4 KB)  TX bytes:10076 (10.0 KB)

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:157 errors:0 dropped:0 overruns:0 frame:0
          TX packets:157 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:11378 (11.3 KB)  TX bytes:11378 (11.3 KB)

[email protected]:~$ lsusb
Bus 001 Device 002: ID 148f:7601 Ralink Technology, Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 046d:c52e Logitech, Inc.
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[email protected]:~$ uname -r
3.13.0-29-generic
[email protected]:~$ uname -a
Linux desktop 3.13.0-29-generic #53-Ubuntu SMP Wed Jun 4 21:02:19 UTC 2014 i686 i686 i686 GNU/Linux
[email protected]:~$ sudo lshw -C network
[sudo] password for yaj:
  *-network               
       description: Ethernet interface
       product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: [email protected]:01:00.0
       logical name: eth0
       version: 02
       serial: 00:e0:4c:64:05:d2
       size: 100Mbit/s
       capacity: 100Mbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.2 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s
       resources: irq:40 ioport:e800(size=256) memory:fdfff000-fdffffff memory:fdfe0000-fdfeffff
[email protected]:~$ sudo modprobe mt7601Usta
modprobe: FATAL: Module mt7601Usta not found.
[email protected]:~$ lsmod
Module                  Size  Used by
bnep                   18895  2
rfcomm                 53664  0
bluetooth             342263  10 bnep,rfcomm
joydev                 17101  0
hid_generic            12492  0
snd_hda_codec_realtek    51029  1
usbhid                 46997  0
snd_hda_intel          42730  3
snd_hda_codec         164067  2 snd_hda_codec_realtek,snd_hda_intel
hid                    87604  2 hid_generic,usbhid
snd_hwdep              13272  1 snd_hda_codec
snd_pcm                85501  2 snd_hda_codec,snd_hda_intel
snd_page_alloc         14230  2 snd_pcm,snd_hda_intel
gpio_ich               13229  0
snd_seq_midi           13132  0
snd_seq_midi_event     14475  1 snd_seq_midi
i915                  705574  3
snd_rawmidi            25135  1 snd_seq_midi
snd_seq                55383  2 snd_seq_midi_event,snd_seq_midi
video                  18903  1 i915
snd_seq_device         14137  3 snd_seq,snd_rawmidi,snd_seq_midi
drm_kms_helper         46907  1 i915
snd_timer              28584  2 snd_pcm,snd_seq
drm                   243792  4 i915,drm_kms_helper
snd                    60871  16 snd_hda_codec_realtek,snd_hwdep,snd_timer,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi
lpc_ich                16864  0
i2c_algo_bit           13197  1 i915
soundcore              12600  1 snd
serio_raw              13230  0
mac_hid                13037  0
parport_pc             31981  1
ppdev                  17391  0
lp                     13299  0
parport                40836  3 lp,ppdev,parport_pc
psmouse                91033  0
r8169                  61562  0
mii                    13654  1 r8169
[email protected]:~$ sudo modprobe -r mt7601Usta
modprobe: FATAL: Module mt7601Usta not found.
[email protected]:~$ sudo modprobe mt7601Usta
modprobe: FATAL: Module mt7601Usta not found.



Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on June 08, 2014, 11:34:33 am
Did you compile the driver without error ?
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: mandeepmails on June 11, 2014, 03:59:00 pm
Sorry to keep you waiting..

Yes, i followed and all steps as mentioned (ditto) on top of that i clearly observed the results in terminal alongwith each and every command i executed..there were no errors.

One close observation though, on top right menu (Network) i don't have wireless even mentioned..

In case i haven't answered your concern still, i can again execute the all commands again and this times attach the whole terminal results/logs in text file.
Thanks so much for helping me out.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mark Greaves (PCNetSpec) on June 12, 2014, 01:57:59 pm
This:-

Quote
[email protected]:~$ sudo modprobe -r mt7601Usta
modprobe: FATAL: Module mt7601Usta not found

kinda tells me the driver can't have compiled/installed correctly.

Can you try again .. but keep an eye out for errors .. particularly when you run the:
Code: [Select]
make
and
Code: [Select]
sudo make install
commands.
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: hinumol on September 17, 2020, 09:36:55 am
Dear all,
I am new user in kali linux, I am using kali from virtualbox windows 10. I tried many time connect my Leo-hg150N usb adapter in kali linux, I can't Possible connect. I commant sudo iwconfig that is showing only wlan0 only. I have internet connect but that only ethernet modem did't show my usb adapter name. and tried airodump-ng wlan0mon. but not get bssid. can you help me...?

thanks & regards
Hinu
Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Keith on September 17, 2020, 11:14:17 am
Hello Hinu  - and welcome to the Forum.

Kali Linux looks very dubious to me.  I found on https://www.linuxmint.com/download_lmde.php (https://www.linuxmint.com/download_lmde.php) "  Kali Linux is made for the express purpose of penetration testing. It is built on the Debian codebase and is created by a security firm known as Offensive Security."
And on https://www.quora.com/What-are-differences-between-Linux-Mint-and-Kali-Linux?share=1 (https://www.quora.com/What-are-differences-between-Linux-Mint-and-Kali-Linux?share=1)  "1 advantage of kali over other distros is it can mount ntfs partitions even when not safely turned off from windows or its hibernated. and you can install other general purpose software as per needed.

For general purpose use, Mint would be the better option and there is much more support for it.   What are you using Kali for? 

For a start, try:
Code: [Select]
iwlist scan | grep ESSID
and post the output here.  Is your router or modem listed?

keith

Title: Re: leoxsys LEO NANO 150N usb wireless adapter on linux mint 16 not working
Post by: Mad Penguin on September 17, 2020, 12:22:04 pm
Hi Guys,

My understanding is that Kali is designed and built explicitly for penetration testing, which is a real requirement for large software projects. i.e. to find out if the project you are about to deploy have any predictable security flaws that could be exploited by third parties. I'm not sure it's designed to be treated as a generic distribution for general use. If you're not a penetration tester by trade, starting with Mint, Ubuntu or KUbuntu might be a better bet.

 :)

hth
SimplePortal 2.3.3 © 2008-2010, SimplePortal